Systems
Gate Automation
Access, surveillance, alerting and physical security, specified against the property.
Answer
What this system does
An automation system moves an existing or new gate under powered control, with appropriate safety devices and control measures, and manual or emergency operation arrangements according to the selected system.
Sliding and swing gates use different mechanisms and suit different sites. A sliding gate needs run-back space alongside the opening; a swing gate needs clear arc on the side it opens toward.
Applications
Typical applications
- Automating an existing manual gate
- Replacing failed or ageing automation
- New gates being fabricated with automation planned in
- Estate and compound entrances
- Commercial and industrial vehicle entrances
Property types: House · Villa · Apartment building · Shop or office · Factory or warehouse · Hotel or resort · Farm or plot
Options
System options
| Sliding | Swing | |
|---|---|---|
| Movement | Runs sideways along a track | Swings on hinges through an arc |
| Space needed | Run-back space alongside the opening | Clear arc on the opening side |
| Often suits | Wide openings, sloping approaches | Sites with room to swing |
| Ground condition | Track and level matter considerably | Hinge and post condition matter |
| Leaves | Usually one | One or two |
| Common issue | Track debris and binding | Post movement and hinge wear |
Site
What the site decides
Measurements
- Opening width, with the unit
- Gate height, with the unit
- Number of leaves
- Estimated gate weight, if known
- Run-back space, for a sliding gate
- Swing arc clearance, for a swing gate
- Distance to the nearest suitable power point
Power
Power is needed at or near the gate. Where there is none, getting a supply there is often the largest single item in the job, and it has to be established before anything else is decided.
Network
Only required where phone or app control is wanted. A gate can be fully automated with remotes and a keypad and no network at all.
Backup
Battery backup keeps the gate operating through a power cut. Whether it is worth it depends on how often supply fails and whether there is another way in. Manual or emergency operation is a separate consideration, and its requirement depends on the system, the property and applicable safety considerations.
Controls
Remote handsets, keypad, RFID, phone or app, or a combination. More control methods means more devices to configure and hand over, which affects both cost and installation time.
Compatibility
Existing automation can sometimes be repaired or partially reused, and sometimes not. Whether a controller, motor or safety device can be retained depends on its make, model, age and condition, and is confirmed at survey.
Safety
Safety considerations
Safety devices are part of the system, not an accessory. A powered gate is heavy and moves under force. Appropriate safety devices and control measures can help reduce the risk of contact, trapping or obstruction when correctly selected, installed and configured. The final safety arrangement depends on the gate type, motor and controller, site layout, manufacturer guidance and applicable safety requirements. This website is not a substitute for a site-specific safety assessment.
Manual or emergency operation requirements depend on the system, property access requirements, manufacturer specification and applicable safety considerations. Where one is fitted, whoever uses the gate should be shown how it works.
Existing systems
Replacing or extending
Where automation already exists and has failed, the make and model plate is a particularly useful photograph. It determines whether parts are available and whether a repair is realistic against a replacement.
Expansion: Additional controls, a keypad, RFID or app access can usually be added later. Whether that is straightforward depends on the controller installed, which is worth asking at specification rather than afterwards.
Prepare
What to photograph
- The gate, whole, from a few steps back
- The opening, showing its width
- The track and its condition, for a sliding gate
- The hinges and posts, for a swing gate
- Any existing motor, including its make and model plate
- The nearest power point, and the route from it to the gate
What may be enough initially: For a straightforward domestic gate with power already at the gate, photographs plus opening width, height and approximate weight are often enough for preliminary guidance.
Plan it
Record your site requirement
The planner records the measurements and site conditions above, and adds them to your requirement.
Cost
What affects the price
- Gate type, size and weight
- Duty expected — how often it moves
- Whether power exists at the gate
- Safety devices selected
- Control methods chosen
- Battery backup
- Cabling and any civil work
- Whether existing equipment is removed
Time
What affects the time
- System size and device count
- Site complexity and cable routes
- Whether a survey is needed first
- Equipment availability for the specification chosen
- Power and network work needed beforehand
- Site access and permitted working hours
- Approvals where a building or association requires them
What can delay installation
- Power or network not ready at the positions agreed
- Access to the site or to working areas
- A specification change after survey
- Civil or structural work needed for mounting or cable routes
- Equipment availability for a specific configuration
Scope
Specification and quotation
What a specification includes
- The devices and where each one goes
- Cabling and containment
- Power and network provision required
- Controls and how the system is operated
- Configuration and handover as quoted
- Anything excluded, stated plainly
What is confirmed at quotation
- Final device selection against site conditions
- Cable routes and quantities
- Any civil or electrical work needed
- Installation scope and working arrangement
- Applicable warranty, commissioning, support and after-sales arrangements
- Price and timing
Process
How it runs
- Initial requirement. What the system needs to do, and where.
- Photographs and measurements. Recorded with the planners.
- Preliminary guidance where appropriate. Indicative only.
- Site survey where required. Power, network, mounting positions and cable routes.
- Final specification. Equipment selected against real conditions.
- Final quotation. Then approval, installation and handover.
Avoid
Common mistakes
- Deciding on a motor before gate weight and travel are known
- Assuming power is available at the gate
- Ignoring track or hinge condition — a gate that binds defeats any motor
- Treating safety devices as an optional extra
- Not knowing how the gate is operated manually when the power fails
Questions
Frequently asked
What information is needed before automating a gate?
Gate type, opening width, gate height, approximate weight, how often it opens, and whether power is available at the gate. Those six let a suitable system be identified.
Photographs of the gate, the track or hinges, and the nearest power point are worth more than a written description.
Sliding gate motor or swing gate automation — what is the difference?
They are different mechanisms suiting different sites. A sliding gate runs sideways and needs run-back space alongside the opening. A swing gate rotates on hinges and needs clear arc on the side it opens toward.
Which suits is usually decided by the site rather than by preference.
What affects gate motor selection?
Gate weight, gate length or travel, and duty cycle — how many times a day it operates. Manufacturers publish limits for each. An unsuitable motor or mechanically difficult gate can overload the system, reduce reliability and shorten equipment life.
We do not select a motor from a photograph. Selection follows real measurements and manufacturer specifications, confirmed at survey.
Can my existing gate be automated?
Often, yes — but the gate has to run freely first. A gate that binds, drags or has worn hinges can overload powered operation, reduce reliability and shorten equipment life. A gate should be mechanically suitable for automation before motor selection. Track and hinge condition are checked at survey.