Security, automation, electrical & IT · Betoda, Ponda, Goa
+91 90750 16328 · Mon–Sat 9:30–18:30

Home › Systems › IT & Network Devices

Systems

IT & Network Devices

Access, surveillance, alerting and physical security, specified against the property.

Answer

What this category covers

Network infrastructure is what security and automation systems increasingly run on. IP cameras, access control, intercoms and remote access all depend on a network that reaches the right places with the right capacity and, often, power over the same cable.

This category covers the equipment that carries and powers those systems: routers and gateways, managed and unmanaged switches, PoE switches, injectors and extenders, Wi-Fi access points and mesh equipment, network racks and wall cabinets, patch panels, keystones, faceplates and patch cords, structured cabling and connectors, fibre media converters, SFP modules and fibre accessories, UPS and power backup, surge protection and power distribution, and network storage where genuinely required.

Available categories and models are confirmed against the requirement. Nothing on this page states what is held. Current models and availability are confirmed against the requirement.

Where it is used

How security systems depend on the network

CCTV

IP cameras require appropriate network connectivity at each position — depending on the system, that connectivity may be wired or wireless — and often power over the same cable where wired. The recorder needs somewhere to live with power and connectivity. Remote viewing needs a usable internet connection.

Access control

Networked systems allow central management across doors. Standalone readers need no network but are managed door by door.

Intercom

App access and networked intercom systems depend on the network reaching both the entry point and the indoor stations.

Homes and offices

Wired points, Wi-Fi coverage, and somewhere tidy for the equipment to live — usually planned alongside the security systems rather than after them.

Router and switch

Router or gateway versus network switch

Router / gatewayNetwork switch
Main jobConnects different networks; commonly manages internet and network routingConnects wired devices within a network
Adds portsA fewIts primary purpose
Wi-FiOften built inNot normally
PoESometimes, on some modelsAvailable on PoE models
Typical useThe point where the network meets the internetWherever wired devices gather

Firewall, VPN and similar capabilities vary by model and are not present on every router. Where those functions matter, they are checked against the actual model specification rather than assumed.

Managed switches

Managed versus unmanaged

Unmanaged switches provide network connectivity with minimal configuration. Plug devices in and they communicate.

Managed switches may provide configurable functions such as VLANs, monitoring, redundancy and traffic controls — depending on the model. Not every managed switch offers the same feature set.

Managed equipment is not automatically better for every job. It costs more, needs configuring, and needs someone able to maintain it. It earns its place where segmentation, monitoring or traffic control are genuinely needed — separating CCTV from office traffic being a common example.

PoE

Power over Ethernet

PoE allows compatible equipment to receive data and power through suitable Ethernet infrastructure — useful for IP cameras, access points, intercom stations and access-control devices where supported.

What has to be checked rather than assumed:

  • Device compatibility — not every camera or access point takes PoE
  • PoE standard and power class — PoE compatibility and power requirements must be checked between the powered device and the supplying equipment. Standards, power classes and non-standard implementations can differ
  • Per-port requirement — what each device actually draws
  • Total PoE power budget — a switch has a limit across all ports, not just per port
  • Cable quality and distance
  • Manufacturer specification for both ends
We do not provide an automatic PoE sizing calculator. Budget depends on the actual devices, their standards and their draw, and getting it wrong means devices that power up individually but drop out together.

Wi-Fi

Router Wi-Fi, access points and mesh

Router Wi-Fi suits smaller properties where one device can reach everywhere. Access points place coverage where it is needed and connect back to the network, usually by cable. Mesh systems coordinate multiple wireless units and may use wireless or wired backhaul depending on the system, which helps where cabling is impractical. Controller-based business Wi-Fi adds central management across several access points.

What affects coverage: property size, wall construction, number of floors, number of users and devices, which areas actually need coverage, interference from neighbouring networks, whether wired backhaul is possible, the internet connection, and what the existing network already provides.

Coverage cannot be promised from floor area alone. Wall construction alone can change it substantially. We do not recommend an access point count from a form — that follows the site.

Cabling

Structured cabling

Structured cabling means running cable to fixed points, terminating it at a patch panel, and patching from there — rather than long individual runs to each device. It makes later changes far easier.

Cable categories commonly specified include Cat5e, Cat6, Cat6A and fibre. Which are supplied is confirmed against the requirement.

What matters: the cable category against what the equipment needs, run distance, whether PoE is carried, termination quality, patch panels and racks, labelling, and testing. Performance figures follow the applicable standards and manufacturer information for the products used.

Existing cable can sometimes be reused, depending on category, condition, termination and route. Testing it is usually quicker than assuming either way.

Racks

Network racks and cabinets

A rack or wall cabinet holds equipment together, mounted and cabled tidily. What typically goes in: a switch, a router, an NVR, a patch panel, a UPS, a power distribution unit, fibre termination and cable management.

Not every system needs one. A single switch in a cupboard does not.

What we ask for: available space, where the rack would go, whether wall or floor mounted, the equipment list, power at that position, ventilation considerations, how cables enter, and what expansion is likely.

We record ventilation considerations. We do not perform thermal engineering.

Power

UPS and power backup

Network devices, CCTV recorders, routers, switches and access-control controllers may benefit from appropriate power backup. A recorder without backup stops recording; a router without it takes remote access with it.

What we ask for: the equipment list, input ratings where known, desired backup time, any existing UPS, local power conditions, and which equipment is actually critical.

We do not calculate UPS capacity automatically. Final selection follows the actual equipment load and manufacturer data.

Fibre

Fibre networking

Fibre can be useful for longer network runs, where electrical isolation between buildings is required, for high-capacity backbone connections, or for inter-building links.

What we capture: source location, destination, approximate route distance, any existing fibre, single-mode or multimode where already specified, the number of links, termination requirements, and the equipment or interfaces at each end.

Distances and specifications follow the applicable standards and manufacturer data. Final design follows project and manufacturer requirements.

Existing networks

Upgrading what is already there

Much of this work is an upgrade rather than a new build. What determines how straightforward it is: the existing router and switches, whether cabling exists and what category it is, whether a rack is already in place, and how the current network is arranged.

Photographs of the existing equipment, including model plates, and any network diagram, are often the useful things to send.

Plan it

Record your network requirement

The IT & Network Requirement planner records the property, the devices, the existing network and the site conditions, and adds them to your requirement.

This page explains concepts. It does not design a network. Access point counts, switch sizing, PoE budgets, UPS capacity, bandwidth, VLAN design, router and firewall specification, fibre type and cable category all follow the actual site, device list, manufacturer data and security requirements — not a form.

Quotation

What information is required before quotation

  • Property type, size and number of floors
  • What the network has to do — new, upgrade, Wi-Fi, PoE, CCTV network, or a combination
  • Number of wired points required
  • Number and type of PoE devices, if known
  • Approximate number of Wi-Fi users and devices
  • Existing router, switches, rack and cabling
  • Internet connection available
  • Whether UPS or backup is required
  • Any network segmentation requirement
  • Photographs of existing equipment, and any network diagram
Photos, measurements and requirement information may support preliminary guidance or an initial quotation where appropriate. A site survey is required where necessary before final system specification, installation scope and final quotation are confirmed.

Avoid

Common mistakes

  • Assuming every IP camera takes PoE, and every PoE switch suits every camera
  • Sizing a PoE switch on port count without checking the total power budget
  • Expecting Wi-Fi coverage from floor area, without accounting for wall construction
  • Reusing existing cabling without testing it
  • Filling every switch port on day one with no spare capacity
  • Leaving the recorder and network without backup power
  • Choosing managed equipment nobody is available to configure or maintain

Questions

Frequently asked

What is the difference between a router and a switch?

A router or gateway connects different networks and commonly manages internet and network routing. A switch connects wired devices within a network.

Many small installations use a single device that does both, plus Wi-Fi. On larger sites they are usually separate, and a switch is added to provide the wired ports the router does not have.

What is a PoE switch?

A switch that can also supply power to compatible equipment through the Ethernet cable, so a camera or access point needs one cable rather than a cable plus a nearby socket.

PoE compatibility and power requirements must be checked between the powered device and the supplying equipment — standards, power classes and non-standard implementations can differ — and the switch has to have enough power available across all the ports in use.

Does every IP camera use PoE?

No. Some cameras take PoE, some need a separate power supply. PoE compatibility and power requirements must be checked between the powered device and the supplying equipment — standards, power classes and non-standard implementations can differ, so it is checked against manufacturer specifications rather than assumed.

What is a managed network switch?

A switch offering configurable functions, which depending on the model may include VLANs, monitoring, redundancy and traffic controls. An unmanaged switch provides connectivity with minimal configuration.

Managed equipment is not automatically the right answer — it costs more and needs configuring and maintaining. It earns its place where segmentation, monitoring or control are actually needed.

When is a network rack useful?

Where several pieces of equipment live together — a switch, a router, a recorder, a patch panel, a UPS — a rack keeps them mounted, ventilated and cabled tidily, and makes later work far easier.

Not every system needs one. A single switch in a cupboard does not.

Do CCTV cameras need internet access?

Not to record locally. A locally recorded CCTV system can normally continue recording without internet access. Cloud-dependent systems may behave differently.

Internet is needed for remote viewing on a phone or from elsewhere, and for some cloud features.

Can CCTV work if the internet is down?

A locally recorded system can normally continue recording, because the cameras and recorder are on the local network. Remote viewing stops until the connection returns, and cloud-dependent systems may behave differently.

Whether recording continues through a power cut is a different question, and depends on backup arrangements.

What information is needed before installing business Wi-Fi?

Property size and layout, wall construction, number of floors, how many users and devices, which areas need coverage, the internet connection, and whether wired cabling can reach the proposed positions.

Coverage cannot be predicted from floor area alone — wall construction changes it substantially, and we do not recommend an access point count from a form.

What is the difference between an access point and a Wi-Fi router?

A Wi-Fi router provides routing, switching and Wi-Fi in one device. An access point provides Wi-Fi coverage and connects back to an existing network, usually by cable.

Access points suit larger properties, because several can be placed where coverage is actually needed rather than relying on one device to reach everywhere.

Do I need a UPS for CCTV and network equipment?

It depends what the system has to do during a power failure. A recorder without backup stops recording; a router without backup takes the network and any remote access with it.

We do not calculate UPS capacity from a form. Selection follows the actual equipment load and manufacturer data.

Can existing network cable be reused?

Sometimes. It depends on the cable category, its condition, how it was terminated, the route it takes and what the new equipment requires — particularly where PoE is involved.

Testing existing cabling is usually quicker than assuming either way.

When is fibre useful instead of copper Ethernet?

Commonly for longer runs, where electrical isolation between buildings is wanted, or for higher-capacity backbone links.

Distances and specifications follow the applicable standards and manufacturer data for the equipment chosen. We do not quote distance limits here.

WhatsApp us